Raspberry Pi Pico and LTR390 UV Light Sensor circuitpython example

In this article we connect a LTR390 UV Light Sensor to the Raspberry Pi Pico

Sensor Information

This sensor converts light intensity to a digital output signal capable of direct I2C interface.

It provides a linear ALS response over a wide dynamic range, and is well suited to applications under high ambient brightness.

The sensor has a programmable interrupt with hysteresis to response to events and that removes the need to poll the sensor for a reading which improves system efficiency.

This CMOS design and factory-set one time trimming capability ensure minimal sensor-to-sensor variations for ease of manufacturability to the end customers.

Features

I2C interface capable of Standard mode @100kHz or Fast mode @400kHz communication; 1.8V logic compatible
Ambient Light / Ultraviolet light(UVS)Technology in one ultra-small 2x2mm ChipLED package
Very low power consumption with sleep mode capability
Operating voltage ranges: 1.7V to 3.6V
Operating temperature ranges: -40 to +85 ºC
Built-in temperature compensation circuit
Programmable interrupt function for ALS , UVS with upper and lower thresholds
RoHS andHalogen free compliant

UVS/ALS Features

• 13 to 20 bits effective resolution
• Wide dynamic range of 1:18,000,000 with linear response
• Close to human eye spectral response
• Automatic rejection for 50Hz/60Hz lighting flicker

This is the sensor that I bought

Parts Required

The sensor you can pick up in the $6 price range – you can connect to the sensor using a standard header the classic dupont style jumper wire.

I used a Qwiic cable – since a few sensors seem to use these but this is optional

Name	Link
Pico	Raspberry Pi Pico Development Board
LTR390	Adafruit LTR390 UV Light Sensor – Stemma QT/Qwiic
Connecting cables	Aliexpress product link Lysee 3D Printer Parts & Accessories – AHT20 Temperature and Humidity Sensor Module DHT11 Upgrade I2C XD Humidity Sensor Probe – (Color: Green) Ebay link

 

Schematic/Connection

I used the Adafruit LTR390 sensor and in this case used the Stemma connection

For the STEMMA QT cables, it uses the Qwiic convention:

Black for GND
Red for V+
Blue for SDA
Yellow for SCL

So color coded for ease of use, this layout shows a connection to the module

Code Example

I used Thonny for development and I am using Circuitpython

You will need to download and install the latest circuitpython from the citrcuitpython download site

The following is based on a library which you can download the zip bundle from https://github.com/adafruit/Adafruit_CircuitPython_Bundle/releases

Before you continue make sure your board’s lib folder or root filesystem has the adafruit_msa301.mpy, adafruit_bus_device, and adafruit_register files and folders copied over on the RP2040 – https://circuitpython.org/libraries

This is the basic example which comes with the library

import time
import board
import busio
import adafruit_ltr390

i2c = busio.I2C(scl=board.GP21, sda=board.GP20)
ltr = adafruit_ltr390.LTR390(i2c)

while True:
    print("UV:", ltr.uvs, "\t\tAmbient Light:", ltr.light)
    print("UVI:", ltr.uvi, "\t\tLux:", ltr.lux)
    time.sleep(1.0)

 

Output

Here is what I saw in Thonny REPL window

UV: 0 Ambient Light: 79
UVI: 0.0 Lux: 63.2
UV: 0 Ambient Light: 79
UVI: 0.0 Lux: 63.2
UV: 0 Ambient Light: 80
UVI: 0.0 Lux: 63.2
UV: 0 Ambient Light: 1
UVI: 0.0 Lux: 0.8

 

Links

Datasheet